Pool Light Repair and Replacement in Fort Worth, Frisco, Lewisville, and most of the DFW Metroplex
Lucent Pools repairs and replaces pool lights in Fort Worth, Frisco, Lewisville, and most of the DFW Metroplex. We find whether the light, gasket, transformer, or power failed, then fix that. Call 817-339-6770.
- Based in Dallas–Fort Worth, serving Fort Worth, Frisco, Lewisville, and most of the DFW Metroplex.
- We can often fix it same day or next day when parts and schedule allow.
- Hours: Monday through Friday, 8:00 AM to 6:00 PM. Saturday closed. Sunday closed.
- We repair in-ground pools and in-ground spas. We do not repair portable hot tubs.
Last updated:

How much does pool light repair cost?
It depends on what failed: the bulb, the lens gasket, the light fixture, the transformer, or the power to the light. Pool light repair and replacement starts at $200 plus applicable tax. Service calls start at $85, plus applicable tax. The service call fee goes toward the labor for your repair if you go ahead with it within 30 days. If you don't, the service call fee is still due. Starting rates exclude tax and parts. Final pricing depends on the equipment, parts, and brand. Lucent Pools is insured. Call 817-339-6770.
See our rates on the pool repairs page.
Starting rates as of October 2026.
Why won't my pool light turn on?
The most common causes are a tripped GFCI or breaker, a switch or automation setting that's off, a failed bulb or LED board, or a failed transformer on a 12-volt light. Start by checking the switch and resetting the GFCI once. If it won't stay on, stop and call.
A new bulb doesn't help when the fault is the GFCI, the transformer or the power feed. For lights run from an automation panel, see pool automation repair.
Pool light keeps tripping the GFCI or breaker
A light that trips the GFCI is telling you current is leaking where it shouldn't, most often water inside the light or a damaged cord. Don't keep resetting it. Leave it off and have it checked.
We check and reset the GFCI and test from the breaker to the light.
Water inside the pool light
Water or fog inside the lens usually means the lens gasket or the cord seal has failed. Turn the light off at the breaker and leave it off until it's opened and dried, resealed, or replaced.
For a leak at the niche itself, see pool leak detection and repair.
Light flickering, stuck on one color, or out of sync
On color lights, flicker, a stuck color or lights that don't match usually come from the control side: how the switch or automation cycles power, the controller, or the wiring between them. A light that dims and recovers can also be protecting itself from heat. We check the controller and wiring before replacing the light.
Can a pool light be fixed without draining the pool?
Most pool light repairs and replacements are done with the pool full. We only drain it if there's another problem, like broken conduit or a clogged line.
Always turn the light off at the breaker before anyone touches it, and never run a light out of the water.
Repair or replace: should I switch to an LED light?
A new gasket, bulb, or board fixes many lights. When the fixture is failing or it's an older incandescent or halogen light, replacing it with an LED light is often the better fix.
Some LED lights aren't serviceable, so the whole light is replaced.
If replacement is needed, we usually recommend Jandy, since new Jandy equipment we install carries a 3-year warranty, but you choose, and we'll install your current brand.
Pool light brands we work on
We service and repair all pool equipment brands, including Jandy, Pentair, and Hayward. We are an Authorized Jandy ProEdge Warranty Station and can also help with Pentair and Hayward warranty claims.
That includes Jandy WaterColors and Infinite WaterColors lights, Pentair IntelliBrite and Amerlite lights, and Hayward ColorLogic lights.
When to call a pro
Call when: the GFCI trips again after one reset; there's water or fog in the lens; the light is cracked, loose in the niche, or the cord is damaged; it works only some of the time; or the colors won't respond.
A homeowner can check the switch or automation setting and reset the GFCI once; anything that trips again, has water in it, or needs the light opened is a service call.
What we do and don't do on pool electrical
We repair anything electrical on your pool, from pumps, heaters, and automation to timers, salt systems, and pool lights, and connect or disconnect it on your existing circuits.
We don't add new circuits or do panel work.
We replace pool lights, including pulling the new light's cord through your existing conduit, and replace light transformers on your existing circuits.
We check and reset the GFCI and test from the breaker to the light.
Warranty
Repair workmanship is covered for 90 days. Parts carry their manufacturer's warranty, and new Jandy equipment we install carries a 3-year warranty through our Jandy ProEdge status.
- 25+ Years in the Pool Business.
- Authorized Jandy ProEdge Warranty Station
- Lucent Pools is insured.
- Lucent Pools is CPO certified by the Pool & Hot Tub Alliance (PHTA).
- Family and veteran owned.
Frequently Asked Questions
Why does my pool light keep tripping the GFCI?
It usually means water has gotten into the light or the cord is damaged, so current is leaking where it shouldn't. Leave the light off rather than resetting it again and again. We find where the leak is and reseal or replace the light. Call 817-339-6770.
Do you have to drain the pool to fix a pool light?
Most pool light repairs and replacements are done with the pool full. We only drain it if there's another problem, like broken conduit or a clogged line. Always turn the light off at the breaker before anyone touches it, and never run a light out of the water. Call 817-339-6770.
Why is there water in my pool light?
Most often the lens gasket or the cord seal has worn out. Turn the light off at the breaker and leave it off. We open it, replace the gasket, and test it, or replace the light if the inside is damaged. Call 817-339-6770.
Why won't my pool light work after I changed the bulb?
The bulb may not have been the problem. A tripped GFCI, a failed transformer on a 12-volt light, a switch or automation setting, or damaged wiring can all keep a light dark. We test from the breaker to the light to find it. Call 817-339-6770.
Do you repair and replace Jandy, Pentair, and Hayward equipment?
Yes. We repair all major brands, including Jandy, Pentair, and Hayward. If a repair will do the job, we fix the equipment you have. When something needs replacing, we usually recommend Jandy. As a Jandy ProEdge builder and dealer and an Authorized Jandy ProEdge Warranty Station, we can give you a 3-year warranty on new Jandy equipment. The choice is always yours, though. If you'd rather stay with your current brand, we'll supply and install that instead.
What is covered under the repair warranty?
Repair workmanship is covered for 90 days. Parts carry their manufacturer's warranty, and new Jandy equipment we install carries a 3-year warranty through our Jandy ProEdge status.
How much does pool light repair cost?
Pool light repair and replacement starts at $200 plus applicable tax. Service calls start at $85, plus applicable tax. The service call fee goes toward the labor for your repair if you go ahead with it within 30 days. If you don't, the service call fee is still due. Starting rates exclude tax and parts. Final pricing depends on the equipment, parts, and brand. Call 817-339-6770.
pool repair in Fort Worth, Frisco, Lewisville, and most of the DFW Metroplex
common pool equipment problems
Hours: Monday through Friday, 8:00 AM to 6:00 PM. Saturday closed. Sunday closed.
